Application of open type Hall current sensor in power distribution system modification in a Russian factory

時間：2021-06-23

朱鹍
安科瑞電氣股份有限公司上海嘉定

Abstract: According to the principle, characteristics and installation mode of the open-type Hall current sensor, the application of the open-type Hall current sensor in the transformation and distribution system of the factory is analyzed, so as to provide a solution for users to realize the intelligent distribution of DC system quickly.

Key words: open type Hall current sensor DC distribution system working principle application

0 Overview
DC distribution system is usually composed of high frequency switching power supply and battery, which is used to provide reliable DC power supply for control, **, relay protection and automatic devices, accident lighting and so on in DC system. It has high requirements for the reliability, stability and quality of power supply. Therefore, in the Russian DC system, we matched the DC Hall distribution meter used. During the transformation of DC system, there is no power outage, and the engineering transformation is difficult, and the traditional closed Hall current sensor or shunt can not solve the problem. Therefore, the open Hall current sensor can be used to solve the DC current measurement problem in the transformation project, so as to ensure the safe operation of the transformation process without power outage.

1 Product Design
1.1Structural features
Open-mouth Hall current sensor is developed on the basis of traditional closed-mouth Hall current sensor. It has novel structure and beautiful appearance. The whole is composed of shell, iron core, sampling circuit board and fixed resin. The shell material is made of PC/ABS alloy, which has the characteristics of high temperature resistance, high mechanical strength and environmental protection. The core is made of oriented cold bonded silicon steel sheet, which has the characteristics of stable performance, high mechanical strength and extremely high magnetic conductivity. Green pluggable terminal is used for circuit board and external wiring, which is convenient and reliable for on-site wiring. The specific structure is shown in Figure 1 and 2. The appearance of the product adopts split design. Figure 1 is a round pass, which is suitable for passing through the DC system when the primary bus is a cable. , Fig. 2 square pass, suitable for the DC system when the primary bus is copper bar. According to the measurement range of primary current and perforation requirements, the corresponding product type can be selected. This series of sensors can measure the current range of 20A ~ 20000A, the main shape of the phi 20, 40, 60, 64*16, 85*27, 104*36, 140*50 and other specifications, as shown in Figure 3, suitable for different applications.

Fig. 1 circular pass pattern Fig. 2 Square pass pattern

Figure 3 AHKC series open type Hall current sensor

1.2 Working principle
Hall current sensor based on hall effect, electromagnetic induction principle, design of a sensor, according to the principle can be divided into the open loop mode (straight) and closed loop mode (magnetic balance type), open hall current sensor is in a traditional open loop (straight) is improved on the basis of hall sensor, is different from traditional single core, single chip design hall, In order to design a split structure, the iron core is separated and installed symmetrically. The hardware adopts parallel complementary differential input of double Hall chips. The principle of open-type Hall sensor is shown in Figure 4:

Fig. 4 Schematic diagram of open Hall sensor

When the primary side current IP flows through a long wire, will produce a magnetic field around the wire, the size of the magnetic field and is proportional to the current through the wire, the magnetic field gathered in the circular, through two hall element in the circular air gap measurement, two hall element marks instead placed in the same field, the output ** with complementary characteristics of output voltage by differential amplifier output, Not only can suppress the common mode interference, but also the influence of temperature drift, the output voltage VS accurately reflect the original side current IP. The general rated output is calibrated as DC±5V or DC4-20mA.

1.3 Product installation
Take square-hole products as an example, as shown in Figure 5, open the mounting screw of the open-type Hall current sensor, and remove the lower body of the sensor; The upper body of the open type Hall current sensor is loaded into the primary bus of the distribution system, and the lower body of the sensor is closed. The mounting screws and gaskets of the sensor pass through the fixing holes of the upper and lower bodies, and the upper and lower bodies of the sensor are fixed together. If on-site power off installation is possible, two corresponding threaded holes can be opened on the bronze plate according to the sensor spacing requirements, and the sensor is fixed on the threaded hole of the bus bar through the rear mounting fixing hole to complete the installation of the sensor; If the site requires continuous electric installation, the supporting rubber pad can be embedded between the shell and the bronze plate to ensure that the sensor can work reliably under vibration conditions. The whole installation process is relatively quick and simple.

Fig. 5 Product installation diagram

1.4 Advantages of open type Hall sensor
Compared with the traditional DC current measurement method generally adopted by shunt or transformer, the open-type Hall sensor has the following advantages:
1) High insulation strength of primary side and secondary side, up to AC 12KV isolation;
2) No insertion loss;
3) Good dynamic performance: the response time is less than 20uS and the tracking speed Di /dt is higher than 20A/ uS
4) There is no need to disassemble the original side cable or bus during installation. It is especially suitable for the transformation and construction of equipment that is not allowed to lose power.

2. Product application
Open-end Hall current sensor is mainly used in the transformation of DC distribution system in factories, such as DC power system transformation in power plants, DC system transformation in substations, communication room transformation, railway locomotive transformation and other projects. It can convert the central edge DC current ** of the system into standard DC± 5V or 4-20mA output. It plays the role of monitoring and electrical isolation, and can be used with multi-loop monitoring instruments or other electrical measuring instruments.

3.Conclusion
Open-end Hall current sensor plays an important role in the application of DC system because of its simple structure, convenient installation, reliable operation and other good applicability, especially in the renovation project.

Bibliography
1.Solutions For Enterprise Micro-grid System 2020.04

作者簡介：
朱鹍，女，就職于安科瑞電氣股份有限公司，主要研究方向?yàn)槠髽I(yè)能源管控

15000353138

詞條
詞條說明
淺談電力數據中心機柜端配電設計方案及監控產品選型
朱鹍安科瑞電氣股份有限公司上海嘉定 201801?摘要：本文從數據中心末端供配電系統的安全性、可行性角度出發，分析當前電力數據中心機柜端供配電系統的設計方案，以及每種設計方案的優缺點。分析和研究智能母線槽配電方案，對其可靠性、靈活性以及經濟性角度進行深入探討，為關鍵電力負載提供可靠性的用電**。??關鍵詞：數據中心；列頭柜配電；智能母線槽；模塊化列頭柜；可靠性&n
機場航站樓消防應急照明和疏散指示系統設計要點剖析
朱鹍安科瑞電氣股份有限公司上海嘉定201801?前言：剖析了GB51309—2018《消防應急照明和疏散指示系統技術標準》和國家建筑標準設計圖集19D702-7《應急照明設計與安裝》實施后的機場航站樓應急照明和疏散指示系統設計要點，包括系統類型的選擇、地面疏散方向標志燈的設置、系統電壓等級的選擇、線路壓降的控制和供電可靠性的提高，并結合相關規范的要求和具體工程實際情況，經過計算、對比論證
分布式光伏運維平臺在公益場館屋光伏發電系統的應用分析
摘要：2021年9月，國家**印發烷善能源消費強度和總量雙控制度方案》，提出鼓勵可再生能源的使用，支持可再生能源發展。在這樣的政策推動下，光伏發電市場無疑將迎來高質量發展的新機遇?，F(xiàn)結合山東博物館光伏電站日常管理的工作經驗以及其他項目的調研情況，剖析電站運維過程中的幾點問題并給予解決建議，希望能提升電站運營質量，推動我國太陽能發電事業健康發展。關鍵詞：文化公益場館；分布式光伏；并網發電系統；運維
配電能效平臺在城市地下綜合管廊的應用
摘要:電氣設計是綜合管廊設計的重要組成部分，文章對綜合管廊的斷面設計、供配電系統和纜線設計進行了分析闡述，并結合設計案例，簡要總結了綜合管廊電氣設計要點。關鍵詞:綜合管廊；斷面設計；供配電系統；纜線設計引言綜合管廊是指建在城市地下，用于容納兩類及以上城市工程管線的構筑物及附屬設施。它可解決馬路“拉鏈”、空中“蛛網”、能節約釋放大量地下空間、增強管線抗災抗險能力、**城市生命線安全，提高城市綜合承載